stainless steel steam jacketed high shear mixing tank 500L mixing tank with 3600rpm mixing speed
Why use a high shear mixer rather than a simple agitator?
A: Agitators can give satisfactory results for simple duties such as blending like-viscosity liquids, providing in-tank uniformity and promoting heat transfer in jacketed vessels. But if you need to blend liquids of differing viscosities, emulsify, homogenize, disintegrate, solubilize, disperse powders, reduce particle size or accelerate reactions, these tasks cannot readily be achieved with a low shear device. A High Shear mixer can do this and more, cutting your mixing time by up to 90 percent.
high shear mixer
high shear mixer high shear mixing tank here below are hot sell mixing tank structure
high shear mixing tank with Open Lid: No lid or upper head is provided. A stiffening ring will be installed along the rim of the tank to maintain stiffness and shape and to protect the shell.
high shear mixing tank with 1-Piece Lid: A 1 piece lid will be a single disk with a lip and a handle that can be removed by hand or bolted to the rim. It can be made with a slot for the mixer shaft or penetrations for various fitting
high shear mixing tank with 2-Piece Split Lid: This type of lid has a single, stainless steel hinge and a handle. It will be divided into 1/3-2/3 with the larger portion often bolted down for stability. The moveable portion is usually used to provide access for mixer removal or for the addition of ingredients.
|
high shear mixing tank
mixing tank 500L mixing tank
stainless steel high shear mixing tank with 3-Piece Split Lid: Used less often, this lid type has two hinged portions with a handle on each. Often the center portion is bolted down for stability. The moveable portions are usually used to provide access for mixer removal or for the addition of ingredients.
stainless steel high shear mixing tank with Cone Lid: A cone header is the rarest of top heads. Like the cone bottom it is a welded, integral part of the tank. It often will have a fitting in the center used for supply. It will be less expensive than a dished header, but also less capable of holding pressure.Mixers in this kind of head have to be mounted on either a flange or a tri-clamp wall fitting.
|
| stainless steel high shear mixing tank with Dish Lid: A dished header, like its counterpart on the bottom, is a welded, integral part of the tank. It often will have a fitting in the center used for supply. It will be more expensive than a cone header, and it will take longer to manufacture, but it will be more capable of holding pressure. Mixers in this kind of head have to be mounted on either a flange or a tri-clamp wall fitting. |
inner wall mirror polish for high shear mixing tank
surface polish for stainless steel mixing tanks
| 2B Finish: This is the least expensive finish and is suitable for almost all processes except finish processes involving food or pharmaceutical products. The stainless steel mixing tank inside welds will be ground down to remove peaks and sharp edges and discoloration will be removed. The outside welds will be touched up to remove sharp edges and any discoloration caused by welding. |
surface polish for stainless steel mixing tanks
| #4 Finish: #4 finish means that the stainless steel mixing tank inside and "wetted" surfaces are polished to a #4 finish (Ra <32). All inside welds are blended smoothly into the surrounding material and buffed and finished to match. The stainless steel mixing tank outside welds will be touched up to remove sharp edges and bumps and any discoloration caused by welding. This is a more expensive finish and is suitable for all mixing tank processes except the most demanding pharmaceutical products. Higher level finishes can be provided and may be specified during the drawing approval phase. |
stainless steel high shear mixing tank specification
| nominal volume L |
400L |
500L |
600L |
800L |
1000L |
1500L |
| Tank diameter mm |
¢800 |
¢900 |
¢1000 |
¢1000 |
¢1200 |
¢1300 |
| Tank height mm |
800 |
800 |
800 |
1000 |
1000 |
1200 |
| Motor power Kw |
0.5 |
0.75 |
0.75/1.1 |
1.1 / 1.5 |
1.1/1.5 |
1.5 /2.2 |
| Agitator speed rpm |
25rpm, 36rpm |
| Working pressure |
≤0.09Mpa |
| Working temperature |
<100ºC |
| Accessories |
Thermal meter,cleaning ball,level meter … |
insulated / non- insulated mixing tank high shear mixing tank
Audited Supplier 
){kind=link}